• Sign In
  • Sign Up
    Loading ...
View All Updates Mark All Read
  • Home
  • Videos
  • Albums
  • Groups
  • Forum
  • Events
  • About
  • Store

Member Info

  • Profile Type: Regular Member
  • Profile Views: 1,245 views
  • Friends: 0 friends
  • Last Update: July 10, 2020
  • Joined: April 7, 2017
  • Updates
  • Info
  • Forum Posts(2)

Updates

The post was not added to the feed. Please check your privacy settings.
  • Ben Zhang
    Ben Zhang replied to a topic in the forum Support:
    Lénárd Pásztor said:
    I think the servo motor can't do this. The servo has 14 fixed position only. Have you checked the servo, is it on the center? 

    Yes, the servo is centered. 
    • July 10, 2020
  • Ben Zhang
    Ben Zhang replied to a topic in the forum Support:
    Hi, I was having a problem with my car steering. It always goes toward the right a little bit. I checked my lego steering gear, it is centered, the wheel is centered too. So I was trying to see if there's any offset setting in Sbrick I can use to offset...  moreHi, I was having a problem with my car steering. It always goes toward the right a little bit. I checked my lego steering gear, it is centered, the wheel is centered too. So I was trying to see if there's any offset setting in Sbrick I can use to offset my steering, but unfortunately I couldn't find any. The only hope I found is in the profile design where I can set the slide Zero point (or reset point) to a certain value not at center so my car will drive straight, that actually works great but the problem is the value is not refined enough, I can only go 0.1 the minimum, where I need is maybe 0.01 step. So now my car actually goes toward the left a little bit after i built my own profile. Is it possible to set the step to 0.01 instead of 0.1? I think it's limited to the step control chip inside Sbrick. thx  less
    • July 4, 2020
  • Ben Zhang
    Ben Zhang has just signed up. Say hello!
    • April 7, 2017
View More
Loading ...

Info

Personal Information

  • First Name Ben
  • Last Name Zhang

Forum Posts

  • July 10, 2020 5:06 PM CEST
    in the topic Profile Designer in the forum Support
    Lénárd Pásztor said: I think the servo motor can't do this. The servo has 14 fixed position only. Have you checked the servo, is it on the center?  Yes, the servo is centered. 
  • July 4, 2020 9:31 PM CEST
    in the topic Profile Designer in the forum Support
    Hi, I was having a problem with my car steering. It always goes toward the right a little bit. I checked my lego steering gear, it is centered, the wheel is centered too. So I was trying to see if there's any offset setting in Sbrick I can use to offset my steering, but unfortunately I couldn't find any. The only hope I found is in the profile design where I can set the slide Zero point (or reset point) to a certain value not at center so my car will drive straight, that actually works great but the problem is the value is not refined enough, I can only go 0.1 the minimum, where I need is maybe 0.01 step. So now my car actually goes toward the left a little bit after i built my own profile. Is it possible to set the step to 0.01 instead of 0.1? I think it's limited to the step control chip inside Sbrick. thx
Previous
Next
Copyright ©2025  -  Privacy  -  Terms of Service  -  Contact  - 

 

SBrick is carried by Kurbli Kft. LEGO®, the LEGO® logo, the Minifigure®, DUPLO®, the DUPLO® logo, BIONICLE®, the BIONICLE® logo, LEGENDS OF CHIMA®, the LEGENDS OF CHIMA® logo, DIMENSIONS®, the DIMENSIONS® logo, the FRIENDS® logo, the MINIFIGURES® logo, MINDSTORMS®, the MINDSTORMS EV3® logo, MIXELS®, the MIXELS® logo, NINJAGO®, the NINJAGO® logo, NEXO KNIGHTS®, and the NEXO KNIGHTS® logo are trademarks and/or copyrights of the LEGO Group, which does not sponsor, authorize or endorse this web site. ©2018 The LEGO Group. All rights reserved.

Share