Updates

• 
  Roger Bush replied to a topic in the forum Support:

  I am unable to design a profile for the Avtoros Shaman 8X8 (MOC-5360 on rebrickable.com). This MOC uses 2 Sbricks. I am trying to use a joystick for Drive and Steering as shown in step 253 of the instructions.
  The wiring configuration for this MOC uses...  moreI am unable to design a profile for the Avtoros Shaman 8X8 (MOC-5360 on rebrickable.com). This MOC uses 2 Sbricks. I am trying to use a joystick for Drive and Steering as shown in step 253 of the instructions.
  The wiring configuration for this MOC uses one port on each of both bricks for these two functions. How can this be accomplished?
  Thanks, Roger Bush  

  • March 18, 2017
• 
  Roger Bush replied to a topic in the forum Support:

  Balint - Thank you. That resolved my problems. Such a simple solution!
  Roger Bush

  • December 30, 2016
• 
  Alex McQuilkin: Hi Roger
  When you made the profile in profile designer did you double click on each slider and give it a name and a name for the channel?  This is the only thing i can think of that would give you a blank page.  I am at the end of my knowledge, I cant...  moreHi Roger
  When you made the profile in profile designer did you double click on each slider and give it a name and a name for the channel?  This is the only thing i can think of that would give you a blank page.  I am at the end of my knowledge, I cant reproduce the last picture with my iphone or ipad i get the correct info.  I have emailed the S Brick team and asked them to contact you as they can look at the profile and see if something is wrong and give you android advice.  Let me know how you make out.
  
  
  Cheers Alex  less

  • December 29, 2016
• 
  Roger Bush replied to a topic in the forum Support:

  Alex McQuilkin said:
  .... so go to the menu bar at the top of the program and select the lines on the left.  you should see, My creations, Sbricks, Tutorial support and logout.  Select Sbricks make sure the cat truck brick is on it will appear...  moreAlex McQuilkin said:
  .... so go to the menu bar at the top of the program and select the lines on the left.  you should see, My creations, Sbricks, Tutorial support and logout.  Select Sbricks make sure the cat truck brick is on it will appear in a list if you also have the othert model brinck on.  Select the brick and it should open with the name and four ABCD outputs the LED tester and update Firmware.  You should be able to operat the truck functions with the red dot controls to energise each output.  If you dont see the brick to open then you have no power.  At the top Left their is a Firmware version it should be 17.  If necessary try the firmware update.
  
  Alex - I have gone through that sequence a number of times. The red dot conrols work properly and I get the same result when I try to use the Profile: Please set up at least one port! as you can see in the last photo.
  
  
  Now what? Thanks, Roger Bush  less

  • December 29, 2016
• 
  Roger Bush replied to a topic in the forum Support:

  Alex McQuilkin said:
  Looking a my ipad sbrick program I scrolled down to the one I wanted to adjust and selected  the Gear wheel in the control profile I wanted to adjust.  When it opens select the gear wheel in the "Remote control profiles"...  moreAlex McQuilkin said:
  Looking a my ipad sbrick program I scrolled down to the one I wanted to adjust and selected  the Gear wheel in the control profile I wanted to adjust.  When it opens select the gear wheel in the "Remote control profiles" This opens the sbrick settings.
  
  Alex - That is as far as I can go. I'm using an LG phone with Android 4.4.2. The following photos show the sequence as I follow your instructions. The first photo shows 2 creations. the Mack Truck uses a Public Profile and it works fine. The next photo shows what happens when I press the gear wheel next to Cat Truck (Caterpillar truck). The last photo show what happens when I press the gear wheel in the lower right hand corner. At that point the Channel Settings 'button' is unresponsive. That's the end of the road.
  
  
  
  Any thoughts? Really appreciate your help.
  Later, Roger  less

  • December 28, 2016
• 
  Roger Bush replied to a topic in the forum Support:

  Alex McQuilkin said:
  Make sure your brick is on when you load the profile in and get the message to setup a channel and you say yes the brick will open and you can assign your function to the brick inputs when done click the save  click on the arrow...  moreAlex McQuilkin said:
  Make sure your brick is on when you load the profile in and get the message to setup a channel and you say yes the brick will open and you can assign your function to the brick inputs when done click the save  click on the arrow in the my creations section and the control should open.
   
  Alex - I followed those steps exactly and I get the same result. After the message: The Profile has been downloaded successfully. Do you want to set up now? I click OK and I am unable the set Channel Settings.
  This is extremely frustrating. I have spent hours and hours trying to make the Profile work. Am about ready to sell my SBricks on eBay.
  Roger Bush  less

  • December 28, 2016
• 
  Roger Bush replied to a topic in the forum Support:

  Need help making a Profile work.
  I designed a Profile with 3 sliders and a button. The sliders are for Steering, Acceleration and Dumping (dump truck). The button is for Lights On/Off. Saved the Profile.
  Then I downloaded the Profile to My Creation. I...  moreNeed help making a Profile work.
  I designed a Profile with 3 sliders and a button. The sliders are for Steering, Acceleration and Dumping (dump truck). The button is for Lights On/Off. Saved the Profile.
  Then I downloaded the Profile to My Creation. I see a message: The profile has been downloaded successfully. Do you want to set up now? After clicking OK, I see the option for Channel Settings and Clinometer Settings. Clicking on Channel Settings produces no result. Then I saved the Profile. But then when I attempt to use the Profile, I get a message: Please set up at least one port! I assume ports and channels are the same thing. Anyway there is no way to "set up at least one port." If I click SBricks from the pull down menu, I can test the 4 functions I designed for the Profile one at a time. They all work except the Lights button must be held to illuminate the lights. Releasing the button turns off the lights.
  So - 1) How do I get the Profile to work without the "Please set up at least one port!"...    less

  • December 27, 2016
• 
  Roger Bush has just signed up. Say hello!

  • December 19, 2016