Updates

• 
  Fabrice Bovy → Coding app beta test: Hi all,
  can you tell me why I don't have the SBrick Pro app any more on my iPad ?
  When I go to Testflight, it tells me "No App to test"...

  • November 3, 2022
  • - edited
• 
  Fabrice Bovy → Coding app beta test: I have a strange behavior when creating a project on iPad and open it from Windows.
  I had to remove all hubs then add them again and reconfigure all virtual ports.
  
  Is it a normal behavior ?

  • January 5, 2022

  • 
    Lénárd Pásztor yes, the iPadOS fakes the hw address of the hub, so it is always changeing so we not save it.

    • February 17, 2022
• 
  Fabrice Bovy → Coding app beta test: Hi all,
  
  I did some new test with the powered up distance and color sensor and the event "When Color sensor value change" is never fired...
  However, the "When distance sensor value change" is fired...  moreHi all,
  
  I did some new test with the powered up distance and color sensor and the event "When Color sensor value change" is never fired...
  However, the "When distance sensor value change" is fired correctly.
  
  Can you have a look ?
  
  Thanks  

  

  • January 5, 2022

  • 
    Mario Russo Just tried today- Seems to be working

    • July 30, 2022
• 
  Fabrice Bovy commented on Randy Sluder's album.

  

  Rail Swiss Monorail

  Rail Swiss monorail snow plow MOC using the LEGO Monorail Transport System and SBrick. Controls flashing red light, headlights, siren and motion of the monorail.

  • May 15, 2021

  • Fabrice Bovy likes this.
  • 
    Fabrice Bovy Hi, nice MOC.
    What did you use for the siren ?

    • May 15, 2021
  • 
    Randy Sluder Just for fun...

    • May 15, 2021
• 
  Fabrice Bovy liked Randy Sluder's album.

  

  Rail Swiss Monorail

  Rail Swiss monorail snow plow MOC using the LEGO Monorail Transport System and SBrick. Controls flashing red light, headlights, siren and motion of the monorail.

  • May 15, 2021

  • Fabrice Bovy likes this.
  • 
    Fabrice Bovy Hi, nice MOC.
    What did you use for the siren ?

    • May 15, 2021
  • 
    Randy Sluder Just for fun...

    • May 15, 2021
• 
  Fabrice Bovy → Coding app beta test: Hi Lénárd Pásztor,
  after having replied on the post of Marek Klajman, I did some more test with the event "When voltage change value" and it does not work. I can show the calculated percentage on "On Start" but the value never change via "When...  moreHi Lénárd Pásztor,
  after having replied on the post of Marek Klajman, I did some more test with the event "When voltage change value" and it does not work. I can show the calculated percentage on "On Start" but the value never change via "When voltage change value". I ran a 2 train motors for 5 minutes and the value never changes, however after stopping and restarting the project, the shown value has changed but not in "live"...
  Can you have a look ?
  Thanks.  less

  

  Hi Lénárd Pásztor,
  after having replied on the post of Marek Klajman, I did some more test with the event "When voltage change value" and it does not work. I can show the calculated percentage on "On Start" but the value never change via "When...  moreHi Lénárd Pásztor,
  after having replied on the post of Marek Klajman, I did some more test with the event "When voltage change value" and it does not work. I can show the calculated percentage on "On Start" but the value never change via "When voltage change value". I ran a 2 train motors for 5 minutes and the value never changes, however after stopping and restarting the project, the shown value has changed but not in "live"...
  Can you have a look ?
  Thanks.  

  • May 5, 2021

  • Marek Klajman and Hambone like this.
  • 
    Lénárd Pásztor Thanks for reporting this. We are on the fix.

    • May 10, 2021
• 
  Fabrice Bovy has added a new cover photo.

  

  • May 1, 2021
• 
  Fabrice Bovy added 2 new photos.
  Hi,
  I get an error 406 on my sbricks light when updating the firmware...
  Now there are not working any more and I am not able to flash the firmware anymore (error 401).
  I had error 406 on the first one then error 401 each time I tried again. On the...  moreHi,
  I get an error 406 on my sbricks light when updating the firmware...
  Now there are not working any more and I am not able to flash the firmware anymore (error 401).
  I had error 406 on the first one then error 401 each time I tried again. On the second sbrick light, I had directly error 401.
  I restarted the computer but still the same error 401 on both sbricks light.
  What can I do ?  

  • April 25, 2021
  • - edited

  • 
    Lénárd Pásztor Hi! we are on the fix, we report back soon.

    • April 29, 2021
    • -
    • 1 likes this
  • 
    Fabrice Bovy Hi Lénárd Pásztor , do you have some news ?

    • May 7, 2021
  • 
    Fabrice Bovy Hi Lénárd Pásztor, I tried with the new driver and App versions but still same error 401... :/

    • May 11, 2021
• 
  Fabrice Bovy → Coding app beta test: Hi,
  I made some simple tests with the new SBrick Light and I find a bug...
  When I use 2 buttons to trigger set color X in Y seconds on 2 different ports (H and G):
  - Button on port H set color green in 5...  moreHi,
  I made some simple tests with the new SBrick Light and I find a bug...
  When I use 2 buttons to trigger set color X in Y seconds on 2 different ports (H and G):
  - Button on port H set color green in 5 seconds
  - Button2 on port G set color red in 5 seconds.
  When I click on Button, the led on port H shades on green but when I click on Button2 before it ends, I mean before the 5 seconds, the led on port G shades on red and the led on port H turns to green with orange...
  When I do the opposite, click on Button2 then on Button, the led on port G turns off and the les on port H shades to green correctly.
  However, if I wait for the 5 seconds, everything works perfectly.
  Hope my explanation is clear enough  less

  

  • April 22, 2021

  • 
    K Tom Hello!
    Please restart the app with internet connection, and try again!
    We fixed it! Thank you!

    • May 18, 2021
  • 
    Fabrice Bovy I would like to test it but I can't... my 2 SBrick Light are unusable due to a crash during last firmware update... still awaiting a solution

    • May 18, 2021
• 
  Fabrice Bovy commented on Marek Klajman's photo.

  

  Once again picture in english. Hope this will help.

  • April 22, 2021

  • Hambone likes this.
  • 
    Marek Klajman Whatever I try, it looks that it´s not possible to have two slider with different settings to control one motor. I would like to have one slider to control extending boom together with unwinding rope. But also have another slider to control rope drum separatly.

    • April 20, 2021
  • 
    Lénárd Pásztor I see that you update the motor status from multiple loops, so this is why it is not working. You need to modify your code to make sure that the motor receiving value from one slider at a time.

    • April 21, 2021
  • 
    Marek Klajman I´ve find solutions, I´m not using slider, but buttons - not that clean solutions as I thought, but it´s working. If you will find time to try, please show me what you mean.

    • April 21, 2021
  • 
    Fabrice Bovy Hi, you should use events instead of loops...
    Try with "When ... controller change value" in dark green blocks

    • April 22, 2021
    • -
    • 1 likes this
  • 
    Marek Klajman Yap, thanks for good tip. It works,

    • May 1, 2021
    • -
    • 1 likes this
• 
  Fabrice Bovy commented on Lénárd Pásztor's photo.

  

  • January 14, 2021

  • View all 7 comments
  • 
    Lénárd Pásztor thanks for reporting this, we checking it

    • January 12, 2021
  • 
    Lénárd Pásztor can you please include code block sample about the set button value and image hide problem? you can create screenshot if you use right click on the code blocks.

    • January 12, 2021
    • -
    • 1 likes this
  • 
    Fabrice Bovy Hi Lénárd Pásztor ,
    I found it... it a side effect of the new change value block. When I set the slider value to 0 by clicking on the button, it executes the block as the event "value changed" is fired and the execution says : set button value to...  moreHi Lénárd Pásztor ,
    I found it... it a side effect of the new change value block. When I set the slider value to 0 by clicking on the button, it executes the block as the event "value changed" is fired and the execution says : set button value to true...
    So I added an IF slider value <> 0 block on the value change block.  

    • January 14, 2021
  • 
    Fabrice Bovy https://social.sbrick.com/albums/photos/view/809/2509

    • January 14, 2021
  • 
    Lénárd Pásztor Hi! Thanks for the example, we checking it.

    • January 20, 2021
• 
  Fabrice Bovy added 1 photo(s) to the album Wall Photos:

  • January 14, 2021
• 
  Fabrice Bovy → Coding app beta test: Hi Lénárd Pásztor, here are the blocks. I didn't change them since a lot. However, the "Show" and "Set value to true" are still working.

  • January 12, 2021
  • - edited

  • 
    Fabrice Bovy I found it... it a side effect of the new change value block. When I set the slider value to 0 by clicking on the button, it executes the block as the event "value changed" is fired and the execution says : set button value to true...
    So I added an IF...  moreI found it... it a side effect of the new change value block. When I set the slider value to 0 by clicking on the button, it executes the block as the event "value changed" is fired and the execution says : set button value to true...
    So I added an IF slider value <> 0 block on the value change block.  

    • January 14, 2021
  • 
    Fabrice Bovy https://social.sbrick.com/albums/photos/view/809/2509

    • January 14, 2021
• 
  Fabrice Bovy → Coding app beta test: Hello,
  I tried to connect 9 SBricks and 2 PoweredUp hubs but always one (randomly, I mean not always the same device) stays in connecting status...
  Is there a limit on the number of connected devices ?

  • January 4, 2021

  • View all 12 comments
  • 
    Lénárd Pásztor wow what type of tablet are you using?

    • January 20, 2021
  • 
    Fabrice Bovy Microsoft Surface Book 3 (W10 Pro version 20H2) with Bluetooth 5.0.

    • January 22, 2021
    • -
    • 1 likes this
  • 
    Lénárd Pásztor If you can create a landscape video not just only with the interface but the working connected devices it would be very cool, so we can share on our FB for example.

    • January 22, 2021
  • 
    Lénárd Pásztor I've just seen the roller coaster video, wow it is really cool

    • January 22, 2021
  • 
    Fabrice Bovy thanks.
    Now you understand why I don't need to control it and would like to know how I can upload a program into an sBrick

    • January 25, 2021
• 
  Fabrice Bovy → Coding app beta test: Hello,
  I have a question when using the "infrared transmitter".
  Is it normal that the output stops when I hide the transmitter (color sensor on PoweredUp hub) ? Does that mean there is a permanent IR link ? Not like with the Lego controller which just...  moreHello,
  I have a question when using the "infrared transmitter".
  Is it normal that the output stops when I hide the transmitter (color sensor on PoweredUp hub) ? Does that mean there is a permanent IR link ? Not like with the Lego controller which just send an "impulse".
  To demonstrate this, I used 2 IR receiver with 1 transmitter, I run a motor on port A receiver 1, when I run another motor on port A receiver 2, the first motor stops. It is not possible to have both running at the same time.
  Another point, even with the application stopped, it seems that the IR link is still present : the led is flashing on the IR receiver and stops when I hide the transmitter (color sensor on PoweredUp hub).  less

  • December 27, 2020
  • - edited

  • 
    Lénárd Pásztor yes, this is a permanent IR link, I think the LEGO ir remote does the same too.
    If you are using multiple IR receiver with the samce channel they sould act the same. Can you please create a video about your setup, is it interesting that the motor stops.

    • December 28, 2020
  • 
    Fabrice Bovy you can find the video here : https://1drv.ms/v/s!AJ8kVfLlY5W1qS0
    1. the first one is full with the Lego transmitter; I start chanel 1 port A then port B then I switch on chanel 2 and start port A than port B. Everything is running at t(he same time.
    2....  moreyou can find the video here : https://1drv.ms/v/s!AJ8kVfLlY5W1qS0
    1. the first one is full with the Lego transmitter; I start chanel 1 port A then port B then I switch on chanel 2 and start port A than port B. Everything is running at t(he same time.
    2. same but with the App; as soon as I switch from chanel 1 to chanel 2, everything running on chanel 1 stop.  

    • December 29, 2020
• 
  Fabrice Bovy → Coding app beta test: When trying to link a "color and distance sensor" to a PoweredUp hub, the screen is completely freezing...

  

  • December 27, 2020

  • 
    Lénárd Pásztor thanks for the reports, we are checking them

    • December 28, 2020
• 
  Fabrice Bovy → Coding app beta test: Another bug, when using "set brake" instruction with a PoweredUp hub, the application is totally out of control...
  The motor don't stop but moreover, you loose all other controls

  

  • December 27, 2020
• 
  Fabrice Bovy → Coding app beta test: Hi all,
  I found a bug when trying to link a "LED on hub" with a PoweredUp hub.
  The screen is completely freezing :

  

  • December 27, 2020
• 
  Fabrice Bovy → Coding app beta test: Lénárd Pásztor do you have some news regarding train motor and poweredup hub ?
  Is it an issue with the new driver ?

  • November 20, 2020

  • 
    Lénárd Pásztor Hi! I ordered a train motor, waiting for arrive, hopefully this week from LEGO.

    • November 30, 2020
    • -
    • 1 likes this
  • 
    Fabrice Bovy Hi Lenard, I try the train motor with the new driver version and it works fine. It didn't say "not supported" anymore.
    Well done!

    • December 20, 2020
    • -
    • 1 likes this
• 
  Fabrice Bovy → Coding app beta test: Another problem...
  I start coding a new project called "New City Train" on Yesterday but what a surprise this morning when open it again : all code disappears...
  Can you have a look ?
  Same problem with my "Goink" project, code behind the Fire button...  moreAnother problem...
  I start coding a new project called "New City Train" on Yesterday but what a surprise this morning when open it again : all code disappears...
  Can you have a look ?
  Same problem with my "Goink" project, code behind the Fire button disappear...  

  • November 9, 2020
  • - edited

  • 
    Lénárd Pásztor we published a new version from the app, and the new one not compatible with the older projects. Do you need access for the old code? Then hopefully I can send you a project file, but you can't import that to the new app.

    • November 11, 2020
  • 
    Fabrice Bovy No, it's ok. It was just to let you know in case of a bug...

    • November 12, 2020
• 
  Fabrice Bovy commented on Mark Bollobas's video.

  SBrick Pro beta app preview - one app to rule them all!

  This is a preview of the SBrick Pro app, it is still a closed beta version with no public access. The app will enable you to control a wide range of Bluetoot...

  • November 8, 2020

  • View all 8 comments
  • 
    Jack No particular projects. Im just really enjoying the Scratch programming of the Mindstorms set, and would have loved to add control of the Buwizz as an extra power source. Controlling everything through a game pad is just the cherry on the cake. I cant...  moreNo particular projects. Im just really enjoying the Scratch programming of the Mindstorms set, and would have loved to add control of the Buwizz as an extra power source. Controlling everything through a game pad is just the cherry on the cake. I cant wait for the app, and now actually looking at your light kits  

    • November 11, 2020
    • -
    • 1 likes this
  • 
    Salvador Otero Alonso There will be a firmware for actual SbrickPus? ..

    • December 8, 2020
  • 
    Salvador Otero Alonso Do you have tested these adaptors https://pv-productions.com/product/power-functions-to-powered-up-adapter/ ... Can you get all the control of a powerup range sensor or motor with the actual sbrickplus hub with these cables or do you think is better to...  moreDo you have tested these adaptors https://pv-productions.com/product/power-functions-to-powered-up-adapter/ ... Can you get all the control of a powerup range sensor or motor with the actual sbrickplus hub with these cables or do you think is better to use Lego's hubs (Buwizz or PfxBrick hubs).  

    • December 8, 2020
  • 
    Salvador Otero Alonso The new firmware of srick plus, Could be accessible from pybriks.com set of instructions or Brick automation project .. or instead, you will publish a new set of phyton functions

    • December 8, 2020
  • 
    Lénárd Pásztor The adapters works only with output devices. About python, we want to enable python programming too inside the SBrick Pro app in the next releases.

    • December 21, 2020
    • -
    • 1 likes this
• 
  Fabrice Bovy → Coding app beta test: Hi, I tried to change the background of my app by adding a gradient one but now, I can't open my app again... That's just a little bit annoying Can you help ?

  

  • November 7, 2020
• 
  Fabrice Bovy → Coding app beta test: Hi,
  I finally succeeded to connect my PowerUp hub inside my project and assigned a device (motor) but it does not work...
  
  I saw your comment saying that you did not test it yet so please, let me know as soon as train motor are supported....  moreHi,
  I finally succeeded to connect my PowerUp hub inside my project and assigned a device (motor) but it does not work...
  
  I saw your comment saying that you did not test it yet so please, let me know as soon as train motor are supported. Thanks
  
  PS : still have to try after firmware update  

  • October 28, 2020

  • 
    Lénárd Pásztor This motor is works with the same hub and the LEGO app, right?

    • October 28, 2020
  • 
    Fabrice Bovy yes, right

    • October 28, 2020
  • 
    Lénárd Pásztor ok, let's check the firmware version of the hub.

    • October 28, 2020
  • 
    Fabrice Bovy fw is 1.0.03.0000 on hardware 0.1.00.0000
    It was not updated by the Lego app

    • October 28, 2020
  • 
    Fabrice Bovy Lénárd Pásztor firmware is now 1.1.02 but still saying "train motor not supported"... I tried with a smart motor and a color/distance sensor and it works well. Any Idea ?

    • November 5, 2020
• 
  Fabrice Bovy → Coding app beta test: I cannot see it in my project in Hubs in range...

  

  • October 25, 2020

  • 
    Lénárd Pásztor what type of hub you are missing? what build are you using?

    • October 28, 2020
  • 
    Fabrice Bovy it is a PowerUp hub from set 60197 - City train

    • October 28, 2020
  • 
    Lénárd Pásztor strange, I have the same two port hub and it works. Maybe you need to update the hub's firmware with the LEGO app.

    • October 28, 2020
  • 
    Fabrice Bovy will try that and keep you posted

    • October 28, 2020
• 
  Fabrice Bovy → Coding app beta test: Hi, I tried to connect the new power up hub, however:
  - it says "train motor not supported"... why ?
  - I cannot see it in my project in Hubs in range...

  

  • October 25, 2020
  • - edited

  • 
    Lénárd Pásztor we will support it, but we haven't tested yet.

    • October 28, 2020
• 
  Fabrice Bovy → Coding app beta test: Hi,
  I have a question : how can I inverse value of a slider with Pro app ?
  I mean, I have a locomotive with 2 motors, I would like to have a slider to control those 2 motors... but the motors are mounted in opposite position. So, when my slider goes...  moreHi,
  I have a question : how can I inverse value of a slider with Pro app ?
  I mean, I have a locomotive with 2 motors, I would like to have a slider to control those 2 motors... but the motors are mounted in opposite position. So, when my slider goes from 0 to X, I need value from 0 to X for the first motor and values from 0 to -X for the second motor  

  

  • October 24, 2020

  • 
    Lénárd Pásztor you can multiple by -1 using a math function

    • October 28, 2020
    • -
    • 1 likes this
  • 
    Fabrice Bovy Thanks Lénárd.

    • October 28, 2020
• 
  Fabrice Bovy Hi,
  I see in the documentation that SBrick cqn execute code in memory. Can you tell me how to launch the code into the SBrick ?

  

  • June 25, 2020

  • 
    Lénárd Pásztor The SBrick can do it, but we not enabled this function yet. We found that more limited than using a controller. What is the function what you want to do without a controller?

    • July 1, 2020
  • 
    Fabrice Bovy I automated the RollerCoaster with my old RCX and I wanted to changed it with a Sbrick+. I really don't need a controller for that...

    • July 4, 2020
  • 
    Lénárd Pásztor What does the current automation do exactly?

    • July 10, 2020
  • 
    Fabrice Bovy Hi Lénárd Pásztor,
    I added a video of my Roller Coaster here : https://1drv.ms/v/s!AJ8kVfLlY5W1qS0
    The automation launch the roller, when it pass over the captor, the second one is launched and the flash is blinking simulating a snapshot. it runs...  moreHi Lénárd Pásztor,
    I added a video of my Roller Coaster here : https://1drv.ms/v/s!AJ8kVfLlY5W1qS0
    The automation launch the roller, when it pass over the captor, the second one is launched and the flash is blinking simulating a snapshot. it runs during 5 minutes then stop.  

    • January 12, 2021
• 
  Fabrice Bovy → Coding app beta test: Hi,
  it is a long time i cannot connect to the beta app...
  It always says "Not a valid email or password" or "facebook login fail"
  Can you help...  moreHi,
  it is a long time i cannot connect to the beta app...
  It always says "Not a valid email or password" or "facebook login fail"
  Can you help ?
  
  Does it exist a desktop version or only the web interface ?  

  • June 24, 2020
  • - edited

  • 
    Lénárd Pásztor hi Fabrice, Which version are you using? mobile or browser?

    • July 1, 2020
  • 
    Fabrice Bovy I m using the browser version on windows 10

    • July 3, 2020
  • 
    Fabrice Bovy I get the same result with Edge or Chrome

    • July 3, 2020
• 
  Fabrice Bovy → Coding app beta test: What's the aim of this button ?

  

  • April 3, 2020

  • 
    zackhariah macasaet i would like to know as well

    • April 12, 2020
• 
  Fabrice Bovy replied to a topic in the group Coding app beta test:

  it should be interesting to add a Trigger section.
  
  Indeed, when initializing your app on a start event, triggering an event can avoid code duplicated by "simulating" the touch start...  moreit should be interesting to add a Trigger section.
  
  Indeed, when initializing your app on a start event, triggering an event can avoid code duplicated by "simulating" the touch start event.
  
  For example:
  I would like to initialise all switches of my ...  

  • April 3, 2020