Same problem over here: I just installed the latest version of the Android app, but my custom prifile is not showing up in the market.
Using: Sony Z3 Compact, Android 4.4.4
just tried to make a new profile in PD.
New profile not appearing in marketplace on ipad/app.
Thanks.
COnor
nothing has changed for me. No profiles visible in app.
Do I need to uninstall SBrick app and then re-install it vis TestFlight to pick up any changed that you have made?
thanks
Conor
UPDATE:
tried uninstalling then re-installing.
app crashes when you log-in to marketplace.
re-start app and you are logged in.
Still no profiles appearing for me - even though they are clearly visible in Profile Designer and have only been edited since they were last used successfully after initial release of PD.
Thanks for ongoing support.
COnor
[blockquote]Conor Davies said:
Just tried to update a profile (following NXT 45 R's suggestion), but was unable to do so on my ipad mini, even though I could see the changes I had made on my computer using the Profile Designer.
Re-installed SBrick (3.6, build 158) app via Testflight (ios 8.1.2, ipad Mini).
usual crash after first log-in.
re-started app.
tried to 'add profile' - was prompted to 'Log In' - but no profiles now visible for me!
I have Profile Designer open on my PC and can see the profile I have made (and was using until 20 minutes ago).
On my ipad I get the message 'You haven't got custom profiles yet. use the profile designer at.......'
So, thoroughly confused now and have taken a backwards step with my SBrick.
Please can someone advise on what I might have done wrong?
many thanks.
[/blockquote]
Are you using the right aspect ratio when you created the profile. As I know iPad has 4:3.
Just tried to update a profile (following NXT 45 R's suggestion), but was unable to do so on my ipad mini, even though I could see the changes I had made on my computer using the Profile Designer.
Re-installed SBrick (3.6, build 158) app via Testflight (ios 8.1.2, ipad Mini).
usual crash after first log-in.
re-started app.
tried to 'add profile' - was prompted to 'Log In' - but no profiles now visible for me!
I have Profile Designer open on my PC and can see the profile I have made (and was using until 20 minutes ago).
On my ipad I get the message 'You haven't got custom profiles yet. use the profile designer at.......'
So, thoroughly confused now and have taken a backwards step with my SBrick.
Please can someone advise on what I might have done wrong?
many thanks.
[blockquote]juerg siegenthaler said:
hello
Have the problem that when I add a profile, it does not turn to the Android app will appear ..
The problem I have only been this morning ...
Have the whole day again and again trying to solve the problem I've uninstalled the app and the profiles have deleted and recreated.
What is going wrong ???
[/blockquote]
Are you using the right aspect ratio (that matches with your mobile device) when you creating the profile?
hello
Have the problem that when I add a profile, it does not turn to the Android app will appear ..
The problem I have only been this morning ...
Have the whole day again and again trying to solve the problem I've uninstalled the app and the profiles have deleted and recreated.
What is going wrong ???
[blockquote]Conor Davies said:
Could I please request a 'RESET' button for the Profile Designer - just like the one used for the Port Tester in the SBrick app?
I would like to have a slider that does not auto-reset when you take your finger off it, but that can be turned OFF by use of a RESET button. This button will also reset the slider to the desired 'ZERO' position.
I hope that, since this feature has already been programmed in to the SBrick app , this shouldn't be too difficult to transfer across to the Profile Designer...
Could someone respond a let me know if my request is:
a) reasonable
b) possible
c) likely to happen in the near future, please?
This would allow me to set the speed of a motor and release the slider, and then switch it OFF when desired. At present it is nearly impossible to manually slide the slider to the exact position where the motor turns OFF and no signal is sent to the motor.
Many thanks
Conor
[/blockquote]
Hi Conor, I think that if you name a button & a slider the same (with the slider set to NOT reset) then you might be able to do this. Also set the button's to output to 0.
Could I please request a 'RESET' button for the Profile Designer - just like the one used for the Port Tester in the SBrick app?
I would like to have a slider that does not auto-reset when you take your finger off it, but that can be turned OFF by use of a RESET button. This button will also reset the slider to the desired 'ZERO' position.
I hope that, since this feature has already been programmed in to the SBrick app , this shouldn't be too difficult to transfer across to the Profile Designer...
Could someone respond a let me know if my request is:
a) reasonable
b) possible
c) likely to happen in the near future, please?
This would allow me to set the speed of a motor and release the slider, and then switch it OFF when desired. At present it is nearly impossible to manually slide the slider to the exact position where the motor turns OFF and no signal is sent to the motor.
Many thanks
Conor